Runco VX-2c Guia de Configuração

VX-2cOWNER’S OPERATING MANUALDigital Light Processing Projector and DHD Controller

DHD CONTROLLER DESCRIPTION REAR PANELPb Pr YVideo3IRRS-232 ControlS-Video 1S-Video 2HD1HD212PrRYGPbBRPrGYBPbHVDVI 1 DVI 2DVI OutH/VVHPrRYGPbBHVTRIGGER

REMOTE CONTROL DESCRIPTION(1) ON/OFFSwitches Power ON/OFF. (This does not operate when POWER/STANDBY indi- cator of the main unit is off.)(2) IR OU

The VX-2c is designed to receive only digital input signals directly from the companion DHD Controller/Processor. All signal sources should be connect

QUICK SETUP GUIDE12Step IConnection:1. Connect Power to Both Projector and DHD controller2. Connect DVI output from the DHD to projector DVI in3. C

While there are many different ways to connect your source equipment to your DHD Controller, the examples below are the most common.ANALOG INPUTS:• Co

14LENS SHIFT RANGELens Option 1: Throw Distance 1.2 - 1.4 x Width of ScreenExample: 56” x 100” ScreenTD = 120” to 140” lens to screenWhen only Vertica

15LENS SHIFT RANGELens Option 4: Throw Distance 2.35 - 3.60 x Width of ScreenExample: 56” x 100” ScreenTD = 235” to 360” lens to screenWhen only Verti



17» PROJECTOR CONTROLOnce the VX-2c and DHD controller have been properly installed and connected, you are ready to perform set-up a

This is the first menu that will appear when “MENU” is selected. The above diagram depicts the main menu. There are five option items in the Main

1TABLE OF CONTENTSIntroduction ...

19MENU DESCRIPTION AND NAVIGATIONOrientOrientUse Preference window to select projector picture orientationFrom the Main menu use the Up or Down arrow

20MENU DESCRIPTION AND NAVIGATIONProj. InfoModelS/NHardware RevisionFirmware RevisionError CodeFrom the Main menu use the Up or Down arrow to select “

21MENU DESCRIPTION AND NAVIGATIONGainRedGreenBlueGainIndicates you are in the Contrast Setting MenuRed Press ENTER to change the Red Contrast setting

22MENU DESCRIPTION AND NAVIGATIONGammaRedGreenBlueGammaIndicates you are in the Gamma Setting MenuRed Press ENTER to change the Red Gamma setting by u

23MENU DESCRIPTION AND NAVIGATIONDiagnoseNormalColor EnableTestsDiagnoseIndicates you are in the Diagnostics menuNormal Press ENTER to return all Diag

24MENU DESCRIPTION AND NAVIGATIONColorGamutColor SpaceColor TempColorIndicates you are in the Color Settings menuGamut Press ENTER to access the Gamut

25MENU DESCRIPTION AND NAVIGATIONColor EnableRed GreenBlueYellowCyanMagentaColor EnableIndicates you are in the Color Enable menuRed Press ENTER to tu

26MENU DESCRIPTION AND NAVIGATIONTestsTest BlackTest WhiteTest GreenTest RedTest BlueCheck BoardAlignmentH RampV RampTestsIndicates you are In the Int

Color SpaceIndicates you are in the Color Space setting menuHD Press ENTER to select the HD Color SpaceSD NTSC Press ENTER to select the SD NTSC Color

28MENU DESCRIPTION AND NAVIGATIONManualWhite Red Green Blue ManualIndicates you are in the Manual Gamut setting mode using a calibrated colorimeter.

2INTRODUCTION» Introduction to the Runco Video Xtreme™ VX-2c 3-Chip DLP ProjectorRunco steps into the future once again with the Video Xtreme™ VX-2c p

BASIC TROUBLESHOOTING TIPSThe following is a basic troubleshooting guide that can assist you in resolving typical problems may result in normal operat

Baud rate: 19200 (xed)Bits: 8No ParityAll protocol in ASCII formatRS-232 input connector pin numbers: TxD= Pin# 2, RxD= Pin# 3, GnD= Pin# 5Command

Command Parameter Value Stored? Description (min/max) POWER 0/1 NA Turns DHD On and Off

Command Parameter Value Stored? Description (min/max) IHPOS? NA NA Returns input horizontal posit

SPECIFICATIONS33VX-2c PROJECTOR SPECIFICATIONSProjector Type:Digital Light Processing™ (DLP™), 3-chip, 16:9 HD-2, DMD™Native Resolution: 1280 x 720 (1

34DHD™ DIGITAL CONTROLLER SPECIFICATIONSAspect Ratio:Anamorphic, Letterbox, VirtualWide, 4:3 (on either 16:9 or 4:3 screens)Input Standards:NTSC/PALOu

RUMA-0101208-6-04 v5.0Runco International2900 Faber StreetUnion City, CA 94587Ph (510) 324-7777 / Fax (510) 324-93001-800-23-RUNCO

WARNINGS & SAFETY PRECAUTIONS3WARNINGFCC Regulations state that any unauthorized changes or modications to this equipment not expressly approved

4WARNINGS & SAFETY PRECAUTIONSDECLARATION OF CONFORMITYRUNCO PROJECTOR, MODEL VX-2cThis device complies with Part 15 of the FCC rules. Opera

5LIMITED WARRANTYCongratulations on your purchase of a Runco video product and welcome to the Runco family! We believe Runco produces “The World’s Fin

LIMITED WARRANTY6TO OBTAIN SERVICE, CONTACT YOUR RUNCO DEALER:Repairs made under the terms of the Limited Warranty covering your Runco International v

7PROJECTOR DESCRIPTION PROJECTOR ISOMETRIC VIEW PROJECTOR REAR PANELAC Power InDVI InputAC MainSwitchPower Button and Status LEDControl PanelVacuumFl

DHD CONTROLLER DESCRIPTION FRONT PANEL2314 56789101. RUNCO ICON When the Red light is displayed the unit is in Standby, when Blue light is dis