Runco XtremeProjection X-200i Guia de Configuração descarregar pdf (Página 2)

Runco X-200i Series Quick Setup Guide Page 2 020-1201-00 Rev. A (September 2012)

PRELIMINAR

PRELIMINARY

Connecting Other Equipment to the Projector (optional) Lens Adjustments

Using the Active 3D Glasses

Remote Control

1. ON

Use this button to turn the projector on.

2. OFF

Use this button to turn the projector off.

3. Discrete Aspect Ratio Selection Buttons

Press one of these buttons to select an aspect

ratio:

16 : 9: For viewing 16:9 DVDs or HDTV programs

in their native aspect ratio.

4 : 3: Scales the input signal to fit 4:3 sources in

the center of the screen.

LETBOX (Letterbox): For viewing non-

anamorphic (“full-screen”) DVDs on a 16:9 screen.

V-WIDE (VirtualWide): Enlarges a 4:3 image

horizontally in a non-linear fashion to fit a 16:9 full

screen display.

CINEMA: For viewing 2.35:1 source material.

V-CINE (Virtual Cinema): For viewing 16:9

source material on a 2.35:1 screen.

4. Cursor Keys ( , , , )

Use these buttons to select items or settings,

adjust settings or switch display patterns.

ENTER

Press to select a highlighted menu item or confirm

a changed setting.

5. MENU

Press this button to show or hide the OSD

controls.

6. Aspect Ratio Selection Button

Press this button repeatedly to select an aspect

ratio.

7. Source Selection Buttons (1-5):

Press to select a video source. These buttons are

assigned as follows: 1 = HDMI 1;

2 = HDMI 2; 3 = Component 1; 4 = Component 2;

5 = RGB.

8. Contrast

Press to adjust white level.

9. Brightness

Press to adjust black level.

10. Memory Preset Buttons:

ISF NIGHT

Press to recall settings for the current input from

the “ISF Night” memory preset.

ISF DAY

Press to recall settings for the current input from

the “ISF Day” memory preset.

CUST 1

Press to recall settings for the current input from

the “Custom 1” memory preset.

CUST 2

Press to recall settings for the current input from

the “Custom 2” memory preset.

11. 3D Mode Selection Buttons:

3D AUTO

Press to set the 3D Mode to Auto.

3D SBS (Side-by-Side)

Press to set the 3D Mode to 3D Side-by-Side.

3D TAB (Top-and-Bottom)

Press to set the 3D Mode to 3D Top-and-

Bottom.

12. LIGHT

Press momentarily to activate remote backlighting.

3D SYNC

RS-232

USB

COMPONENT 1

12V TRIGGER

III

12V TRIGGER

WIRED REMOTE

HDMI 2

RGB

HDMI 1

COMPONENT 2

POWER

ISSUE

LED STATUS

-23

-2

NEN

NENT

HDMI

RGB

HDMI

NEN

OWE

WER

ISSUE

SSU

LED ST

TUS

LED ST

TUS

AutoScope Lens Motor

AC InputPower

Switch

3D SYNC IN

Active 3D Emitter

Tip = +12V

Sleeve = Ground

Retractable Screen or other

12-volt trigger-activated

device

(3.5-mm, mini

phono plugs)

(3-pin mini-DIN plug)

IR Sensor

IR Repeater

Remote Control

Focus

To focus the projected image, grasp the lens by the front ring and rotate it.

Zoom

To make the picture smaller (zoom out) or larger (zoom in), slide the zoom control in the direction

shown at left.

To lock the position of the lens, tighten the knob with a flat-blade screwdriver.

Vertical Lens Shift

To shift the projected image vertically, first ensure that the lens lock is not engaged. Insert the

provided hex wrench into the vertical lens shift adjuster on the side of the projector. Then, turn the

wrench to shift the lens in the desired direction.

Horizontal Lens Shift

To shift the projected image horizontally, first ensure that the lens lock is not engaged. Insert the

provided hex wrench into the horizontal lens shift adjuster at the top of the projector. Then, turn the

wrench to shift the lens in the desired direction.

Do not attempt any lens adjustments when the lens lock is

engaged. Doing so may cause damage to the zoom or lens shift

mechanisms.

THE LENS SHIFT MECHANISM CAN BE DAMAGED BY

EXCESSIVE FORCE. Do not attempt to move the primary lens beyond

its normal adjustment range.

• Battery Status LED

Indicates battery charge state when glasses are turned on, as

follows:

= Fully Charged (12 - 15 hrs. left)

= 50% Charged (approx. 4 hrs. left)

= 30% Charged (approx. 2 hrs. left)

= ≤10% Charged (must charge glasses

before further use)

• Power Button

Press to turn the glasses on or off.

• Power Input

To chazrge the glasses, connect this input to your PC or other

USB power source, using the included charging cable.

Charging the 3D Glasses

The glasses must be fully charged before first use and whenever

the Battery Status LED flashes red once every couple of

seconds. Charging takes approximately five hours.

1. Attach one end of the supplied charging cable to the Power

Input above the left lens on the glasses.

2. Attach the other end of the cable to any USB “A” port on a

USB hub, personal computer or display device. The Battery

Status LED lights solid red while the battery is charging.

3. When the Battery Status LED lights solid blue, the battery is

fully charged. You can disconnect the glasses from the

power source.

Zoom Out

Zoom In

Focus

Vertical

Lens Shift

Control

Horizontal

Lens Shift

Control

Caution

WARNING

Battery Status

LED (Red/Blue)

Power Button

Power

Input

1 2 3 4

Comentários a estes Manuais

Sem comentários

Runco XtremeProjection X-200i Guia de Configuração Página 2

Comentários a estes Manuais

Manuais e produtos relacionados com Projetores Runco XtremeProjection X-200i