Operation

70 Signature Cinema™ SC-50d/SC-60d Installation/Operation Manual

PRE

IMINAR

•ConstantContrast: Select ConstantContrast from the Display Color - Projector

Settings menu to enable (On) or disable (Off) ConstantContrast in the optical engine.

ConstantContrast uses a dynamic iris that modulates light to the DMD based on the

actual content of the video material. Runco recommends that you disable

ConstantContrast before adjusting Brightness, Contrast or other image settings, or if

you change the RVR setting (see below) to something other than the default value.

•RVR: Use the RVR control to increase or decrease the Reflectance Volume Regulation

setting. RVR lets you adjust the aperture or iris size (the physical opening through the

lens; similar to an “f-stop” on a camera). Doing so allows you to optimize brightness

and contrast according to the amount of ambient light in the viewing area.

Use a lower setting (larger aperture = higher brightness) for rooms with a lot of ambient

light. Use a higher setting (smaller aperture = higher contrast) for more “theater-like”

viewing conditions (little or no ambient light).

Input Image: The Input Image controls are functionally similar to those in the Picture

menu (refer to page 56), but are accessible only by entering the Calibration menu

passcode.

Input Color: The Input Color controls are similar to those in the Display Color menu (see

above), but adjust the color balance of the incoming signal. These settings are also saved

independently for each input and display mode.

•Gain/Offset (HD1, HD2 and Component/SCART inputs only): These controls

operate similarly to those in the Display Color - Common Settings menu (described

on page 65), but affect the Y, Pb and Pr signal components rather than the red, green

and blue channels.

• Chroma Delay: use the Chroma Delay control to correct a mis-aligned image from a

composite video source. Chroma delay in an image causes color shifts to occur to the

left of the vertical edge transitions, producing artificial shadows or a “halo” effect. If

necessary, adjust this setting to eliminate them.

•Nois e Filter: To apply noise filtering to the input signal, select Noise Filter from the

Input Color menu. The Noise Filter is useful for clearing up noisy images from 480i

video sources.

Use the left- or right-arrow buttons to select the desired amount of noise reduction,

keeping in mind that higher settings (which reduce high frequencies) may also “soften”

the image.

Save ISF Night/Save ISF Day: Whenever you make a change to the ISF settings, you

should always save it. Select Save ISF Night or Save ISF Day from the Calibration menu to

do this.

You cannot use ConstantContrast and RVR at the same time (both

controls affect the aperture size, in different ways). Generally, using

RVR to set the total image brightness produces more satisfying

results than using ConstantContrast.

The Input Image settings establish the “zero point” for the Picture

menu settings, whose values represent offsets from the Input

Image settings. For example, if you set Brightness to 10 in this

menu, setting Brightness to 10 in the Picture menu results in an

actual setting value of 20 (10+10).

Note

1 2 ... 81 82 83 84 85 86 87 88 89 90 91 ... 125 126

Comentários a estes Manuais

Sem comentários

Craftsman 172.10855 Handbücher

Bedienungsanleitungen und Benutzerhandbücher für Elektrowerkzeuge Craftsman 172.10855.
Wir stellen 1 PDF-Handbücher Craftsman 172.10855 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungshandbuch

Craftsman 172.10855 Bedienungshandbuch (26 Seiten)

Marke: Craftsman | Kategorie: Power tools | Größe: 0.99 MB |

Inhaltsverzeichnis

71/4-in. CIRCULAR SAWS

SAVETHESE INSTRUCTIONS!

READ ALL INSTRUCTIONS!

ELECTRICAL SAFETY cont

A HAZARDOUS CONDITION

UNPACKING

the guideline

TO MAKE POCKET CUTS

MAKING RIP CUTS cont

To Attach the Rip/Edge Guide

Our Home

1-800-488-1222

Your Home

Weitere Produkte und Handbücher für Elektrowerkzeuge Craftsman

Modelle	Dokumententyp
172.171040	Bedienungshandbuch Craftsman 172.171040 Owner`s manual, 16 Seiten
315.172310	Bedienungshandbuch Craftsman 315.172310 Owner`s manual, 18 Seiten
320.16494	Bedienungsanleitung UNIVERSAL QUICK-RELEASE MOUNTING, 62 Seiten
315.271810	Bedienungshandbuch Craftsman 315.271810 Owner`s manual, 44 Seiten
113.241680	Bedienungshandbuch Craftsman 113.241680 Owner`s manual, 52 Seiten
172.21299	Betreibershandbuch Craftsman 172.21299 Operator`s manual, 32 Seiten
315.273990	Bedienungshandbuch Craftsman 315.273990 Owner`s manual, 14 Seiten
113.248322	Bedienungshandbuch Craftsman 113.248322 Owner`s manual, 48 Seiten
351.211970	Betreibershandbuch Craftsman 351.211970 Operator`s manual, 20 Seiten
315.271410	Bedienungshandbuch Craftsman 315.271410 Owner`s manual, 12 Seiten
875.191183	Bedienungshandbuch Craftsman 875.191183 Owner`s manual [en] , 17 Seiten
113.226640	Bedienungshandbuch Craftsman 113.226640 Owner`s manual, 44 Seiten
CompuCarve 133.217540	Betreibershandbuch Craftsman CompuCarve 133.217540 Operator`s manual, 46 Seiten
170.172450	Bedienungsanleitung Craftsman®… Surround Yourself with Quality, 7 Seiten
130.26620	Betreibershandbuch Craftsman 130.26620 Operator`s manual, 24 Seiten
320.17217	Betreibershandbuch Craftsman 320.17217 Operator`s manual, 20 Seiten
172.107210	Bedienungshandbuch Craftsman 172.107210 Owner`s manual, 10 Seiten
315.115160	Betreibershandbuch Craftsman 315.115160 Operator`s manual, 26 Seiten
113.207600	Betreibershandbuch Craftsman 113.207600 Operator`s manual, 36 Seiten
572	Bedienungshandbuch Craftsman 572 Owner`s manual, 6 Seiten

Runco VX-60d Especificações Página 86

Comentários a estes Manuais

Manuais e produtos relacionados com Projetores de dados Runco VX-60d

Craftsman 172.10855 Handbücher

Craftsman 172.10855 Bedienungshandbuch (26 Seiten)

Inhaltsverzeichnis

Weitere Produkte und Handbücher für Elektrowerkzeuge Craftsman