Runco XtremeProjection X-450d Especificações Página 122
- Página / 156
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
External Control
106 Runco X-400d/X-450d Installation/Operation Manual
PRE
L
IMINAR
Y
Command Format Commands sent from an automation/control system or PC to the Dimension Digital
Controller must have the following format:
(www:xyz) [CR]
Where:
• ( and ) indicate the start and end of the command data. If these characters are
present, the Dimension Digital Controller assumes that valid command data is present
in the command string. Otherwise, the Dimension Digital Controller ignores the
command.
• www indicates the command code. This field is case insensitive; for example, PWR, pwr
and PwR are all equivalent.
• :x is the destination parameter. This is an optional parameter that indicates which
memory the command is referencing. This parameter is reserved for future use.
• y is the operand, which can have one of the following values:
? = “Get” operand + = “Increment” operand
= = “Set” operand - = “Decrement” operand
• z is the value to set for this parameter. It can have one of two formats:
• Integer value: Any positive or negative number; for example, 100.
• String value: Any string surrounded by double quotes; for example, “This is a
string.”
• [CR] is the ASCII carriage return key (0x0D).
Response Format Responses sent from the follower to the initiator shall have the following format:
(u;www:x=z) [CR]
Where:
• ( and ) indicate the start and end of the command data. If these characters are
present, the Dimension Digital Controller assumes that valid command data is present
in the command string. Otherwise, the Dimension Digital Controller ignores the
command.
• “u;” indicates the response code. This is only used by followers responding to a valid
CLI command received. For any response code other than 0, the follower echoes back
the command received rather than filling in the fields listed below.
The response code can be one of the following:
• 0 = Command successfully processed
• 1 = Unknown command code
• 2 = Invalid operator
• 3 = Destination parameter not supported
• 4 = Setting not available
• 5 = Setting value not available
• 6 = Setting value not supported
• 7 = String too long
• 8 = Command not supported in standby mode
• 9 = Invalid parameter
• 10 = Error processing command
➤
➤
- XtremeProjection™ Series 1
- X-400d and X-450d 1
- Warranty 3
- Important Safety Instructions 7
- Compliance Information 9
- Table of Contents 11
- List of Figures 15
- 1. Introduction 17
- Using This Manual 18
- Description, Features 19
- Introduction 20
- 2. System Overview 21
- Projector 22
- 1 2 3 4 65 7 23
- DC-300 Dimension 24
- Digital Controller 24
- System Overview 25
- Remote Control Unit 28
- X-400d/X-450d Active 32
- 3D Emitter 32
- 3. Installation 33
- Quick Setup 34
- Installation 35
- Considerations 35
- Estimating Throw Distance 36
- Throw Distance (TD) = 36
- Screen width (w) 36
- Ceiling Installation 38
- Floor Installation 38
- Installing the Optional 42
- CineWide Lens Mount 42
- Mounting the 48
- Interconnections 50
- Dimension Digital Controller 51
- Audio Processor/ 52
- Switcher 52
- Secondary Display 52
- (to ctrl. system) 53
- (from ctrl. system) 53
- AutoScope Lens Motor 54
- Notebook Computer 57
- HDMI source 58
- COMPONEN T 59
- VIDEO OUT 59
- Computer 60
- Gaming Console 61
- DVD/DTV STB 61
- Camcorder 62
- Active 3D Emitter 63
- Turning on the Power 64
- Adjusting the Image 66
- Geometry 66
- Installing and 68
- Adjusting the 68
- CineWide Anamorphic 68
- Lens threads into ring 70
- Too Far Right 71
- Too Far Left 71
- Correct position 71
- Too High 72
- Anamorphic Lens (Top View) 73
- Correct Lens Angle 75
- Incorrect Lens Angle 75
- Wrong Position 76
- Correct Position 76
- 4. Operation 77
- 4:3 Image on 81
- 16:9 Display 81
- (Letterbox aspect ratio) 81
- 1080i HDTV Image 82
- 720p HDTV Image 82
- Below Black 84
- 3D Processing 91
- Reverse Eyes 91
- 7 Auto Color Enable 96
- 7 Test Pattern Enable 96
- Operation 100
- Primary Alignment 102
- Input Names 103
- SRC 1 Key 105
- Power Button 114
- Battery Status 114
- LED (Red/Blue) 114
- Lamp Replacement 117
- Troubleshooting Tips 118
- 6. External Control 121
- External Control 122
- Table 6-1. Serial Commands 123
- DBO R/W Yes -100 100 No 125
- DGO R/W Yes -100 100 No 126
- DRO R/W Yes -100 100 No 126
- IBO R/W Yes -32 32 No 127
- IGO R/W Yes -32 32 No 128
- IRO R/W Yes -32 32 No 129
- SHO R/W Yes -50 50 No 134
- (VSH+) or (VSH-) to 137
- (ZOM+) or (ZOM-) to 137
- Using Discrete IR 138
- (Standard Mode) 139
- (Standard Mode) (continued) 140
- (Extended Mode) 142
- Controller 143
- (continued) 144
- 7. Specifications 145
- Dimension Digital 148
- Specifications 148
- Supported Timings 150
- X-400d/X-450d 154
- Dimensions 154
- 020-1203-00 Rev. A 156
- September 2012 156
Manuais e produtos relacionados com Projetores de dados Runco XtremeProjection X-450d
Projetores de dados Runco VX-60d Especificações
(126 páginas)
(126 páginas)
Projetores de dados Runco CL-420 Especificações
(72 páginas)
(72 páginas)
Projetores de dados Runco Vision 85 Especificações
(88 páginas)
(88 páginas)
Projetores de dados Runco RS-440LT Especificações
(41 páginas)
(41 páginas)
Projetores de dados Runco VX-8d Especificações
(104 páginas)
(104 páginas)
Projetores de dados Runco VX-2c Guia de Configuração
(36 páginas)
(36 páginas)
Projetores de dados Runco XP-103DHD Especificações
(126 páginas)
(126 páginas)
Projetores de dados Runco VX-4000d Especificações
(108 páginas)
(108 páginas)
Comentários a estes Manuais